| 8/31/2021 |
Calibrated Lift Switch |
Error: Nozzle Offset probe failed |
| 8/25/2021 |
Heated up bowden tube (left in hot car) and end of the filament popped out |
Filament stuck in bowden tube. Soaking the tube in boiling water was also an option |
| 8/25/2021 |
Print core cleaning |
Print core was severely jammed |
| 8/25/2021 |
Reset print head cable |
ER34 Error (couldn't communicate with print head) |
| 8/3/2021 |
Had to send it in to have the firmware reset |
Glowforge wouldn't start, a picture of Tux appeared with the error "U-Boot 2016.05.ultimaker-00017...") |
| 8/2/2021 |
Feeder #2 Cleaning |
Routine Maintenance |
| 8/2/2021 |
Feeder #1 Cleaning |
Routine Maintenance |
| 8/1/2021 |
Print Core #2 Cleaning |
Routine Maintenance |
| 8/1/2021 |
Print Core #1 Cleaning |
Routine Maintenance |
| 7/19/2021 |
Reset print head cable |
ER34 Error (couldn't communicate with print head) |
| 6/16/2021 |
Disassembled and reassembled Feeder #1. Checked the parts and pushed down on them to make sure nothing was loose. |
Filament wasn't being pulled into bowden tube. I suspect part of the feeder may have been lose. |
| 6/7/2021 |
Firmware Update |
Routine Maintenance |
| 6/4/2021 |
Feeder #1 Cleaning |
Routine Maintenance |
| 6/4/2021 |
Feeder #2 Cleaning |
Routine Maintenance |
| 6/2/2021 |
Print Core #2 Cleaning |
Routine Maintenance |
| 6/2/2021 |
Print Core #1 Cleaning |
Routine Maintenance |
| 5/29/2021 |
Reset Print Head Cable |
Wasn't being detected |
| 5/19/2021 |
Feeder 1 Cleaning |
Routine Maintenance |
| 5/19/2021 |
Print Core #1 Cleaning |
Routine Maintenance |
| 5/19/2021 |
Firmware update |
Routine Maintenance |
| 5/6/2021 |
Feeder #2 cleaning |
Routine Maintenance |
| 5/6/2021 |
Feeder #1 cleaning |
Routine Maintenance |
| 5/6/2021 |
Cleaned print AA .04 Print cores |
Routine Maintenance / had to unjam one core |
| 4/30/2021 |
Cleaned print cores |
Routine Maintenance |
| 4/24/2021 |
Reset Print Head Cable |
Wasn't being detected |
| 4/23/2021 |
Print Core #1 Cleaning |
Had recently finished a lot of printing |
| 4/11/2021 |
Calibrated X/Y offeset |
Routine Maintenance |
| 4/11/2021 |
Calibrated Lift Switch |
Routine Maintenance |
| 4/8/2021 |
Cleaned AA .04 Print Core |
Filament wouldn't extrude |
| 4/8/2021 |
Cleaned Feeder #1 |
Feeder was grinding the filament |
| 3/29/2021 |
Updated firmware to 6.3 |
Routine Maintenance |
| 3/22/2021 |
Cleaned the .4BB print core |
Routine Maintenance |
| 3/22/2021 |
Cleaned the .4AA Print Core |
Filament not extruding |
| |
Took print head #2 apart and reset spring |
Even though the print core was being detected, it was still throwing an error |
| 3/15/2021 |
Shifted the spring above the life switch so the print core would fit properly. If it happens again we made need to take the print head apart and completely reset it. |
Print core was not detected |
| 3/4/2021 |
Cleaned .4BB Print Core |
Routine Maintenance |
| 3/4/2021 |
Cleaned .4AA Print Core |
Routine Maintenance |
| 3/2/2021 |
PVA Filament stuck in bowden tube. Had to disconnect the tube entirely to push it out using spare filament. |
Jam |
| 3/2/2021 |
Firmware Update (6.2) |
Routine Maintenance |
| 2/22/22021 |
Firmware Update |
Routine Maintenance |
| 2/1/2021 |
Cleaned .4BB Print Core |
Routine Maintenance |
| 2/1/2021 |
Cleaned .4AA Print Core |
Routine Maintenance |
| 1/27/2021 |
Firmware update (6.1.1) |
Routine Maintenance |
| 12/10/2020 |
Cleaned fan |
Routine Maintenance |
| 12/10/2020 |
Firmware update (5.8.2) |
Routine Maintenance |
| 12/10/2020 |
Clearned .4BB Print Core |
Routine Maintenance |
| 12/10/2020 |
Clearned .4AA Print Core |
Routine Maintenance |
| 11/11/2020 |
Clearned Feeder #2 |
Routine Maintenance |
| 10/30/2020 |
Clearned Feeder #1 |
Routine Maintenance |
| 10/20/2020 |
Cleaned .8AA Print Core |
Routine Maintenance |
| 10/20/2020 |
Firmware update |
Routine Maintenance |
| 10/6/2020 |
Print core cleaning (.4AA and .4BB) |
Routine Maintenance |
| 9/23/2020 |
Firmware update |
Routine Maintenance |
| 9/29/2020 |
Firmware update |
Routine Maintenance |